Corresponding to flashrom svn r220 and coreboot v2 svn r3275.
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
The generic jedec.c does not work for the ST M50FLW flash devices,
because they need an unlock command first. For this reason, ST M50FLW
support is moved to a new HW support module, because any change in
jedec.c would bear the risk to cause problems with the already supported
devices.
It's already tested with ST M50FLW080A; the other chips of this family i
dont have available, so i couldnt test it.
Corresponding to flashrom svn r219 and coreboot v2 svn r3274.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
The read pointer was already checked properly.
Corresponding to flashrom svn r218 and coreboot v2 svn r3273.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Flash pages, which where excluded from updating using the exclude or the
layout option, as well as areas, whose flash contents already contain
the desired data, will be skipped. These ensures absolute data security
of critical areas (BIOS boot block), e.g. against a sudden power off or
a CPU hangup during flashing. As a nice side effect, it speeds up the
flash process, if the BIOS to be flashed is very similar to the version
in flash.
Corresponding to flashrom svn r217 and coreboot v2 svn r3260.
Signed-off-by: Claus Gindhart <claus.gindhart@kontron.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r216 and coreboot v2 svn r3221.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Straight from the datasheet, untested.
Corresponding to flashrom svn r215 and coreboot v2 svn r3167.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Forgot to add the file.
Support for the Winbond W39V080FA series of chips. Support for flashing
on the Kontron 986LCD-M board.
Corresponding to flashrom svn r214 and coreboot v2 svn r3166.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Support for flashing on the Kontron 986LCD-M board.
Corresponding to flashrom svn r213 and coreboot v2 svn r3165.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Corresponding to flashrom svn r212 and coreboot v2 svn r3153.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r211 and coreboot v2 svn r3152.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Corresponding to flashrom svn r210 and coreboot v2 svn r3151.
mechanism.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r209 and coreboot v2 svn r3146.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
This fixes the problem of not being able to erase the chip.
Corresponding to flashrom svn r208 and coreboot v2 svn r3145.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Functionality (except printing) should be unchanged.
Corresponding to flashrom svn r207 and coreboot v2 svn r3144.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Ward says:
This code detects the ICH8 chipset on my laptop, and it appears to use
SPI.
Acked-by: Ward Vandewege <ward@gnu.org>
Corresponding to flashrom svn r206 and coreboot v2 svn r3142.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Cosmetic changes in some files, partly bending the 80-characters-per-line
rule in this special case, as the 80-character-limited version looks
equally crappy even in an 80x25 console/xterm, so let's make it at least
look good in a high-resolution xterm.
Corresponding to flashrom svn r203 and coreboot v2 svn r3139.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Corresponding to flashrom svn r202 and coreboot v2 svn r3138.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
It's just an example, likely never been used in the last few years, and
the contents are available in the README already anyway.
Corresponding to flashrom svn r200 and coreboot v2 svn r3134.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ward Vandewege <ward@gnu.org>
The file was written by Stefan Reinauer for coresystems GmbH in 2005, as
confirmed on IRC.
Corresponding to flashrom svn r198 and coreboot v2 svn r3126.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Also add a comment about NULL subsystem IDs leaving the board entry out
of auto-detection logic.
Corresponding to flashrom svn r197 and coreboot v2 svn r3110.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
With this small change it is possible to build flashrom again when
specifying custom CFLAGS/LDFLAGS from the make command line like.
make CFLAGS="..." LDFLAGS="..."
I need to do this when building flashrom in a cross compiler environment
like buildroot for a foreign target.
Corresponding to flashrom svn r196 and coreboot v2 svn r3102.
Signed-off-by: Clark Rawlins <clark@bit63.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
- Remove the "enable write to flash" message, as the caller appears to
already report that.
- Move the 'modprobe msr' suggestions to the first lseek64 error handling, as
we get an error there already.
- Rename a perror string from "read" to "read msr", as we use the latter
already in this function for another read.
Corresponding to flashrom svn r195 and coreboot v2 svn r3101.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Also, move a big code comment to the top of enable_flash_cs5536().
Corresponding to flashrom svn r193 and coreboot v2 svn r3098.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
This implements support for devices using AMD Geode companion chip
CS5536 that have the Boot ROM on NOR flash that is directly connected to
FLASH_CS3 (Boot Flash Chip Select). We need to write enable it in the
NORF_CTL MSR register for flashrom to be able to write to it, including
JEDEC probe commands.
This patch allows us to stop using AMD gx_utils.ko for BIOS flashing on
the DBE61.
Corresponding to flashrom svn r192 and coreboot v2 svn r3097.
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Some vendors like Programmable Micro Corp (PMC) need this. Both the
serial and parallel flash JEDEC detection routines would benefit from a
parity/sanity check of the vendor ID. Will do this later.
Add support for the PMC Pm25LV family of SPI flash chips.
Corresponding to flashrom svn r191 and coreboot v2 svn r3091.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Chris Lingard <chris@stockwith.co.uk>
The full syntax still works, and is required when two vendors have
boards with the same names.
Corresponding to flashrom svn r190 and coreboot v2 svn r3082.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r188 and coreboot v2 svn r3078.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
Tested on the pcengines alix1c and works fine.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
I've tested and verified the chip myself, and it seems to work
everything like supposted, since Carl-Daniel has patched flashrom to
use the read funktion on verifying.
"benchvice flashrom # ./flashrom -m gigabyte:m57sli -v test.4mb
Calibrating delay loop... OK.
No coreboot table found.
Found chipset "NVIDIA MCP55", enabling flash write... OK.
Found board "GIGABYTE GA-M57SLI-S4": enabling flash write...
Serial flash segment 0xfffe0000-0xffffffff enabled
Serial flash segment 0x000e0000-0x000fffff enabled
Serial flash segment 0xffee0000-0xffefffff disabled
Serial flash segment 0xfff80000-0xfffeffff enabled
LPC write to serial flash enabled
serial flash pin 29
OK.
MX25L3205 found at physical address 0xffc00000.
Flash part is MX25L3205 (4096 KB).
Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED.
benchvice flashrom # ls -l test.4mb
-rw-r--r-- 1 root root 4194304 22. Jan 16:27 test.4mb
Corresponding to flashrom svn r186 and coreboot v2 svn r3072.
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
That fails if the flash chip is not mapped completely. If the read
function is set in struct flashchip, use it for verification as well.
This fixes verification of all SPI flash chips >512 kByte behind an
IT8716F flash translation chip.
"MX25L8005 found at physical address 0xfff00000. Flash part is MX25L8005
(1024 KB). Flash image seems to be a legacy BIOS. Disabling checks.
Verifying flash... VERIFIED."
Corresponding to flashrom svn r185 and coreboot v2 svn r3070.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>
readcnt==0 saves 10 seconds with the unconditional 10us delay, reducing
programming time for SST25VF016B to 40-45 secs.
Corresponding to flashrom svn r183 and coreboot v2 svn r3068.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Because 'v' and 'V' are already in use, the patch uses 'R' (for release)
and, of course, '--version'.
Corresponding to flashrom svn r182 and coreboot v2 svn r3067.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Ulf Jordan <jordan@chalmers.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Corresponding to flashrom svn r180 and coreboot v2 svn r3059.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Corresponding to flashrom svn r179 and coreboot v2 svn r3058.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r178 and coreboot v2 svn r3054.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
After the patch [...] The line length is still below 80 characters.
Corresponding to flashrom svn r177 and coreboot v2 svn r3045.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Acked-by: Torsten Duwe <duwe@lst.de>
The #defines were already there.
Corresponding to flashrom svn r176 and coreboot v2 svn r3042.
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Straight from the data sheet, not tested.
Corresponding to flashrom svn r175 and coreboot v2 svn r3036.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r174 and coreboot v2 svn r3033.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Corresponding to flashrom svn r173 and coreboot v2 svn r3032.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Improve model number printing.
Add EN29F002(A)(N)B support while I'm at it.
Corresponding to flashrom svn r172 and coreboot v2 svn r3031.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Markus Boas <bios@ryven.de>
The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Corresponding to flashrom svn r171 and coreboot v2 svn r3030.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
