The AT25F512B is quite different from the other (older and yet
unsupported) chips in the AT25F* familiy, hence rename 512B-specific
stuff to make room for the generic AT25F* code.
Corresponding to flashrom svn r1583.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
- introduce spi_prettyprint_status_register_atmel_at25_wpen()
- use spi_prettyprint_status_register_bit() where possible
- generify spi_prettyprint_status_register_bp3210 and use it in at25.c too
Corresponding to flashrom svn r1560.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Chip features an optional permanent boot block write protection.
Corresponding to flashrom svn r1522.
Signed-off-by: David Borg <borg.db@gmail.com>
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
This chip needs special command sequences in 8 bit mode. Also, 8 bit
programming needs actually 16bit double byte program.
The chip is found on the Bifferos Bifferboard, for example.
Corresponding to flashrom svn r1521.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Similar to modules using the opaque programmer framework (e.g. ICH Hardware
Sequencing) this uses a template struct flashchip element in flashchips.c with
a special probe function that fills the obtained values into that struct.
This allows yet unknown SPI chips to be supported (read, erase, write) almost
as if it was already added to flashchips.c.
Documentation used:
http://www.jedec.org/standards-documents/docs/jesd216 (2011-04)
W25Q32BV data sheet Revision F (2011-04-01)
EN25QH16 data sheet Revision F (2011-06-01)
MX25L6436E data sheet Revision 1.8 (2011-12-26)
Tested-by: David Hendricks <dhendrix@google.com>
on W25Q64CV + dediprog
Tested-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
on a 2010 MX25L6436E with preliminary (i.e. incorrect) SFDP implementation + serprog
Thanks also to Michael Karcher for his comments and preliminary review!
Corresponding to flashrom svn r1500.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
All programmer access function prototypes except init have been made
static and moved to the respective file.
A few internal functions in flash chip drivers had chipaddr parameters
which are no longer needed.
The lines touched by flashctx changes have been adjusted to 80 columns
except in header files.
Corresponding to flashrom svn r1474.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Struct flashchip is used only for the flashchips array and for
operations which do not access hardware, e.g. printing a list of
supported flash chips.
struct flashctx (flash context) contains all data available in
struct flashchip, but it also contains runtime information like
mapping addresses. struct flashctx is expected to grow additional
members over time, a prime candidate being programmer info.
struct flashctx contains all of struct flashchip with identical
member layout, but struct flashctx has additional members at the end.
The separation between struct flashchip/flashctx shrinks the memory
requirement of the big flashchips array and allows future extension
of flashctx without having to worry about bloat.
Corresponding to flashrom svn r1473.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Push those changes forward where needed to prevent new sign
conversion warnings where possible.
Corresponding to flashrom svn r1470.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
An opaque programmer does not allow direct flash access and only offers
abstract probe/read/erase/write methods.
Due to that, opaque programmers need their own infrastructure and
registration framework.
Corresponding to flashrom svn r1459.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
- probe_timing was changed to unsigned although we use negative values
for special cases
- some code was not changed along hence did no longer compile:
* dediprog's read and write functions
* linux_spi's read and write functions
- it introduced a number of new sign conversion warnings
(http://paste.flashrom.org/view.php?id=832)
To be safe this patch reverts all changes made in r1448, a corrected
patch will follow later.
Thanks to idwer for pointing out the problem first!
Corresponding to flashrom svn r1450.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
This is related to the spi split patch as discussed in:
http://www.flashrom.org/pipermail/flashrom/2010-February/thread.html#2364
the old commit (r914) log notes:
"Some of the spi programmer drivers required chipdrivers.h, needs fixing later: it87spi.c
ichspi.c sb600spi.c wbsio_spi.c buspirate_spi.c ft2232spi.c bitbang_spi.c dediprog.c"
there still remain a few cases where chipdrivers.h is needed:
dediprog.c (spi_read_chunked and spi_write_chunked)
it87spi.c (due to spi_write_enable and spi_read_status_register)
wbsio_spi.c (spi_programmer registration only)
besides that, there are also non-spi files that do not need it.
also, add flash.h to chipdrivers.h because it uses some types of it
and remove flashchips.h from print.c
Corresponding to flashrom svn r1414.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Add lock printing for AMIC A25L05PT, A25L05PU, A25L10PT, A25L10PU,
A25L20PT, A25L20PU, A25L40PT, A25L40PU, A25L80P, A25L16PT, A25L16PU,
A25L512, A25L010, A25L020, A25L040, A25L080, A25L016, A25L032, A25LQ032
to a25.c.
Add lock printing for Atmel AT26DF081A, AT26DF161, AT26DF161A,
AT26DF321.
Move Atmel AT25*/AT26* lock related functions originally added in r1115
from spi25.c to at25.c.
For SPI chips the lock printing was handled by one common function, but
sharing a common function which only is a big switch() statement doesn't
make sense, especially if we can define lock printing functions per
flash chip anyway.
The printlock function pointer in struct flashchip is used to print
status register and locking information, and serves as replacement for
implicit status register and lock printing during probe. That code will
later be changed to store locking info in a machine- accessible data
structure so flashrom can handle locked regions correctly.
Corresponding to flashrom svn r1316.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
As the comment indicates, that function is not a chip erase function
at all, but a function calling a block eraser in a loop. So it adds
no extra value to what we already have in the block_eraser
infrastructure.
Furthermore, that function assumes a uniform sector size layout, but
is referenced from flash chip with non-uniform sector size layout, which
is just wrong.
Corresponding to flashrom svn r1287.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Add code for the unlocking (erasing/writing) of Winbond W39V040FB
chips, enabling erasing/writing this type of chip.
Corresponding to flashrom svn r1248.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Print lock status for all supported Winbond W39* chips:
W39V040A, W39V040B, W39V040C, W39V040FA, W39V040FB, W39V040FC,
W39V080A, W39V080FA, W39V080FA (dual mode).
Fill in correct probe timing for Winbond W39V040C and W39V080FA.
Please note that the W39V040B/W39V040FB pair has identical IDs,
identical read/write/erase, but locking differs. Same applies to
W39V040C/W39V040FC. This causes double detection on chipsets which
support LPC and FWH, making flashing more difficult because the user
has to select the correct chip. This is called the evil twin problem.
A better evil twin handling (patch available) will resolve that problem.
Corresponding to flashrom svn r1245.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
The inner write functions which handle partial write are renamed to the
original name of their wrappers. The write wrappers are removed.
Corresponding to flashrom svn r1211.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Tested-by: Andrew Morgan <ziltro@ziltro.com>
Tested-by: Idwer Vollering <vidwer@gmail.com>
Acked-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Kill duplicated code.
Annotate write functions with their chunk size.
Mark Fujitsu MBM29F400BC and ST M29F400BB as untested because their
write code no longer uses a broken layout.
Corresponding to flashrom svn r1210.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Tested-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Tested-by: Idwer Vollering <vidwer@gmail.com>
Acked-by: Idwer Vollering <vidwer@gmail.com>
Tested-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Sean Nelson <audiohacked@gmail.com>
The currently used write functions (wrappers) all use helpers which
perform the actual write (inner functions).
The signature of the write wrappers is: int write_chip(struct flashchip
*flash, uint8_t * buf);
The signature of the inner write functions varied a lot. This patch
changes them to: int write_part(struct flashchip *flash, uint8_t *src,
int start, int len);
Did you know that flashrom has only 8 inner write functions for all
flash chips? write_page_write_jedec_common write_sector_jedec_common
write_sector_28sf040 spi_chip_write_256_new spi_chip_write_1_new
spi_aai_write_new write_page_82802ab write_page_m29f400bt
Export all inner write functions.
Change the function signature of wait_82802ab to eliminate single-use
variables.
Remove an error message in write_page_m29f400bt which was printed for
every byte written regardless of success.
Add sharplhf00l04.c to the list of flash chip drivers in the Makefile.
While the functions in there are unused, I suspect we will need them
later, and by hooking the file up we ensure that compilation won't
break.
Corresponding to flashrom svn r1208.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Flashrom had an implicit erase-on-write for most flash chip and
programmer drivers, but it was not entirely consistent.
Some drivers had their own hand-rolled partial update functionality
which made handling partial updates from generic code impossible.
Move implicit erase out of chip drivers, and kill some dead erase
functions at the same time. A full chip erase is now performed in the
generic code for all flash chips on write, and after that the whole chip
is written.
Corresponding to flashrom svn r1206.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Use AAI write for SST SST25VF032B.
Speedup from 228 to 113 seconds.
Use page (256 byte) write for SST SST25VF064C.
Speedup from 3091 to 123 seconds.
Corresponding to flashrom svn r1194.
Signed-off-by: Helge Wagner <helge.wagner@ge.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Add support for Atmel AT25DF081A and AT25DQ161.
Some chips require EWSR before WRSR, others require WREN before WRSR,
and some support both variants. Add feature_bits to select the correct
SPI command, and default to EWSR.
Corresponding to flashrom svn r1115.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Steven Rosario
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Use full-chip write function on Fujitsu MBM29F400TC and ST M29F400BT.
Add support for ST M29F400BB.
Corresponding to flashrom svn r1083.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Actually check if the unlock worked instead of just assuming it worked.
Corresponding to flashrom svn r1082.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
However, wrap the write functions in a compat layer to allow converting
the rest of flashrom later. Tested on Intel NM10 by David Hendricks.
Corresponding to flashrom svn r1080.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Besides that, the function as implemented just walks the chip and
ignores sector sizes.
Sector erase with SPI opcode 0xd8 is of course still supported.
Kill a declaration for a nonexisting function while we're at it.
Corresponding to flashrom svn r1054.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Some chips implement the RES (0xab) opcode, but they use a non-standard
two byte response instead of the usual one byte response. A two-byte
response has the accuracy of REMS and RDID, so don't check for REMS/RDID
availability before running a two-byte RES.
Corresponding to flashrom svn r1017.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Every SPI programmer driver had its own completely different chip write
implementation, and all of them were insufficiently commented. Create
spi_write_chunked as a copy of spi_read_chunked and convert all SPI
programmers to use it. No functional changes except: - Bus Pirate uses
12 Byte writes instead of 8 Byte writes - SB600 uses 5 Byte writes
instead of 1 Byte writes
Corresponding to flashrom svn r1005.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: David Hendricks <dhendrix@google.com>
Sst49lfxxxc software status register is functionally the same as the
82802ab status register, "Block Protect Status"(49lfxxxc) can be treated
the same as "Device Protect Status"(82802ab).
Erase_block_49lfxxxc is the same command sequence as erase_block_82802ab.
Add unlock_49lfxxxc to chips definitions.
Write_sector_49lfxxxc is the same as write_page_82802ab.
Corresponding to flashrom svn r972.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Rename print_82802ab_status to print_status_82802ab add unlock_82802ab strip unlock code from erase_block_82802ab rename erase_82802ab_block to erase_block_80280ab delete sharplhf00l04.o from Makefile delete *_lhf00l04* from chipdrivers.h.
add unlock_stm50flw0x0x
delete wait_stm50flw0x0x
delete write_page_stm50flw0x0x
convert erase_stm50flw0x0x to erase_chip_stm50flw0x0x
delete write_stm50flw0x0x
add unlock_82802ab to two Intel chips with TEST_BAD_WRITE
change the status of 82802AB, 82802AC, M50FW040, M50FW080 to TEST_OK_PR
Corresponding to flashrom svn r948.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Convert _sst_fwhub functions to jedec.
Corresponding to flashrom svn r943.
kill unused sst_fwhub.c functions
make unlock_* check if unlock was successful and only return 0 when fully successful
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Remove function probe_28sf040.
Corresponding to flashrom svn r942.
delete references to dead sharplhf00l04.c and sst29sf040.c functions from chipdrivers.h
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
- remove some copied functions (from 82802ab.c) and use the 82802ab equivalents
- fix missing prototypes to *_82802ab functions
Corresponding to flashrom svn r941.
fix missing prototypes to _82802ab functions
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Corresponding to flashrom svn r940.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Corresponding to flashrom svn r939.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Now the only remaining and used function in pm49fl00x.c is unlock_49fl00x.
Also:
- Add missing unlock to AMIC A49LF040A.
- Add lock_49fl00x function.
Corresponding to flashrom svn r917.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
We also need to 'svn rm' the following files:
am29f040b.c
en29f002a.c
m29f002.c
mx29f002.c
pm29f002.c
sst49lf040.c
w49f002u.c
Corresponding to flashrom svn r909.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Convert the following chips to block_erasers: SST28SF040A SST29EE010
SST29LE010 SST29EE020A SST29LE020 SST39SF010A SST39SF020A SST39SF040
SST39VF512 SST39VF010 SST39VF020 SST39VF040 SST39VF080 SST49LF002A/B
SST49LF003A/B SST49LF004C SST49LF008A SST49LF008C SST49LF016C SST49LF020
SST49LF020A SST49LF040 SST49LF040B SST49LF080A SST49LF160C .
Extend sst28sf040 to include chip and sector functions for block_eraser.
Extend sst49lfxxxc to include chip, sector, block erasers functions for
block_erasers. Extend sst_fwhub to include chip and sector functions for
block_erasers. Add copyrights to changed files. Killed erase_sst_fwhub.
Killed erase_49lfxxxc. NULL A/A mux mode full chip erasers. Ignore block
locks in erase/write. Change comments from "PP mode" to "A/A mux mode"
Corresponding to flashrom svn r877.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Convert chips to block_erasers:
SyncMOS S29C31004T
SyncMOS S29C51001T
SyncMOS S29C51002T
SyncMOS S29C51004T
TI TMS29F002RT
TI TMS29F002RB
SyncMOS chips have Uniform sector; boot blocks on chips are made up of uniform sectors but have locking.
Corresponding to flashrom svn r871.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Some mingw declares a global identifier "byte", causing -Werror -Wshadow
to break compilation. This patch renames all identifiers called "byte".
Corresponding to flashrom svn r861.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
- Add eraseblock definitions
- Use correct eraseblock sizes (the datasheet is a bit ambiguous)
- Use correct probe function
- Fill in probe timing
There is a lot more stuff left to clean up, but at least probe and erase
should work now.
Corresponding to flashrom svn r837.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
The patch converts jedec functions into mask-based generics which can
be used for many chip provided the only changes are the addresses are
converted from 0x5555/0x2AAA to 0x555/0x2AA or similar.
The patch mostly changes jedec.c, but a few other files are changed
because they use the jedec functions within their own functions.
The patch also adds a copyright line to flashchips.c because of my
recent work in converting AMD and Atmel chips to use struct erase_block.
Corresponding to flashrom svn r828.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
AMIC_A29002B
AMIC_A29002T
EN_29F002B
EN_29F002T
MBM29F004BC
MBM29F004TC
MBM29F400BC
MBM29F400TC
MX_25L3205
MX_25L6405
MX_29F002B
MX_29F002T
Add block erasers for m29f400bt and mx29f002.
Change programmer delays from 2 seconds to 10us in mx29f002 and am29f040b.
Corresponding to flashrom svn r819.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
