Add new programmer for SPI EEPROMs attached to Intel 82580 NICs

This patch lets you read and write the EEPROM on 82580-based gigabit NIC cards. So far it has been tested on copper NICs only, but other variants employing this controller should work too. It is a nice substitution for the official eeupdate tool. Speed is quite decent: less than 4 seconds for erases or writes of 32 kB. Corresponding to flashrom svn r1832. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
2025-04-26 22:52:34 +02:00 · 2014-07-28 20:35:21 +00:00 · 2014-07-28 20:35:21 +00:00 · 2a41f0a2c0
commit 2a41f0a2c0
parent a5bcbceb58
5 changed files with 379 additions and 3 deletions
--- a/14
+++ b/14
@ -227,6 +227,11 @@ UNSUPPORTED_FEATURES += CONFIG_NICINTEL=yes
 else
 override CONFIG_NICINTEL = no
 endif
+ifeq ($(CONFIG_NICINTEL_EEPROM), yes)
+UNSUPPORTED_FEATURES += CONFIG_NICINTEL_EEPROM=yes
+else
+override CONFIG_NICINTEL_EEPROM = no
+endif
 ifeq ($(CONFIG_NICINTEL_SPI), yes)
 UNSUPPORTED_FEATURES += CONFIG_NICINTEL_SPI=yes
 else
@ -426,6 +431,9 @@ CONFIG_NICINTEL ?= yes
 # Always enable SPI on Intel NICs for now.
 CONFIG_NICINTEL_SPI ?= yes

+# Always enable EEPROM on Intel NICs for now.
+CONFIG_NICINTEL_EEPROM ?= yes
+
 # Always enable SPI on OGP cards for now.
 CONFIG_OGP_SPI ?= yes

@ -626,6 +634,12 @@ PROGRAMMER_OBJS += nicintel_spi.o
 NEED_PCI := yes
 endif

+ifeq ($(CONFIG_NICINTEL_EEPROM), yes)
+FEATURE_CFLAGS += -D'CONFIG_NICINTEL_EEPROM=1'
+PROGRAMMER_OBJS += nicintel_eeprom.o
+NEED_PCI := yes
+endif
+
 ifeq ($(CONFIG_OGP_SPI), yes)
 FEATURE_CFLAGS += -D'CONFIG_OGP_SPI=1'
 PROGRAMMER_OBJS += ogp_spi.o
--- a/flashrom.8.tmpl
+++ b/flashrom.8.tmpl
@ -225,6 +225,8 @@ bitbanging adapter)
 .sp
 .BR "* usbblaster_spi" " (for SPI flash ROMs attached to an Altera USB-Blaster compatible cable)"
 .sp
+.BR "* nicintel_eeprom" " (for SPI EEPROMs on Intel Gigabit network cards)"
+.sp
 Some programmers have optional or mandatory parameters which are described
 in detail in the
 .B PROGRAMMER SPECIFIC INFO
@ -591,7 +593,7 @@ syntax where
 .B content
 is an 8-bit hexadecimal value.
 .SS
-.BR "nic3com" , " nicrealtek" , " nicnatsemi" , " nicintel"\
+.BR "nic3com" , " nicrealtek" , " nicnatsemi" , " nicintel", " nicintel_eeprom"\
 , " nicintel_spi" , " gfxnvidia" , " ogp_spi" , " drkaiser" , " satasii"\
 , " satamv" , " atahpt" ", " atavia " and " it8212 " programmers
 These programmers have an option to specify the PCI address of the card
@ -625,6 +627,14 @@ For more information please see
 .nh
 .B http://flashrom.org/VT6421A
 .SS
+.BR "nicintel_eeprom " programmer
+This is the first programmer module in flashrom that does not provide access to NOR flash chips but EEPROMs
+mounted on gigabit Ethernet cards based on Intel's 82580 NIC. Because EEPROMs normally do not announce their
+size nor allow to be identified, the controller relies on correct size values written to predefined addresses
+within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an unprogrammed
+EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST)
+M95128, M95256 and OnSemi (Catalyst) CAT25CS128.
+.SS
 .BR "ft2232_spi " programmer
 An optional parameter specifies the controller
 type and channel/interface/port it should support. For that you have to use the
@ -922,8 +932,8 @@ need PCI configuration space access and raw memory access.
 .B rayer_spi
 needs raw I/O port access.
 .sp
-.B satasii
-needs PCI configuration space read access and raw memory access.
+.BR satasii ", " nicintel ", " nicintel_eeprom " and " nicintel_spi
+need PCI configuration space read access and raw memory access.
 .sp
 .B satamv
 needs PCI configuration space read access, raw I/O port access and raw memory
--- a/flashrom.c
+++ b/flashrom.c
@ -297,6 +297,18 @@ const struct programmer_entry programmer_table[] = {
 	},
 #endif

+#if CONFIG_NICINTEL_EEPROM == 1
+	{
+		.name			= "nicintel_eeprom",
+		.type			= PCI,
+		.devs.dev		= nics_intel_ee,
+		.init			= nicintel_ee_init,
+		.map_flash_region	= fallback_map,
+		.unmap_flash_region	= fallback_unmap,
+		.delay			= internal_delay,
+	},
+#endif
+
 #if CONFIG_OGP_SPI == 1
 	{
 		.name			= "ogp_spi",
--- a/nicintel_eeprom.c
+++ b/nicintel_eeprom.c
@ -0,0 +1,331 @@
+/*
+ * This file is part of the flashrom project.
+ *
+ * Copyright (C) 2013 Ricardo Ribalda - Qtechnology A/S
+ * Copyright (C) 2011, 2014 Stefan Tauner
+ *
+ * Based on nicinctel_spi.c and ichspi.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see http://www.gnu.org/licenses/.
+ */
+
+/*
+ * Datasheet: Intel 82580 Quad/Dual Gigabit Ethernet LAN Controller Datasheet
+ * 3.3.1.4: General EEPROM Software Access
+ * 4.7: Access to shared resources (FIXME: we should probably use this semaphore interface)
+ * 7.4: Register Descriptions
+ */
+
+#include <stdlib.h>
+#include <unistd.h>
+#include "flash.h"
+#include "spi.h"
+#include "programmer.h"
+#include "hwaccess.h"
+
+#define PCI_VENDOR_ID_INTEL 0x8086
+#define MEMMAP_SIZE (0x14 + 3) /* Only EEC and EERD are needed. */
+
+#define EEC	0x10 /* EEPROM/Flash Control Register */
+#define EERD	0x14 /* EEPROM Read Register */
+
+/* EPROM/Flash Control Register bits */
+#define EE_SCK	0
+#define EE_CS	1
+#define EE_SI	2
+#define EE_SO	3
+#define EE_REQ	6
+#define EE_GNT	7
+#define EE_PRES	8
+#define EE_SIZE 11
+#define EE_SIZE_MASK 0xf
+
+/* EEPROM Read Register bits */
+#define EERD_START 0
+#define EERD_DONE 1
+#define EERD_ADDR 2
+#define EERD_DATA 16
+
+#define BIT(x) (1<<x)
+#define PAGE_MASK 0x3f
+
+static uint8_t *nicintel_eebar;
+static struct pci_dev *nicintel_pci;
+
+#define UNPROG_DEVICE 0x1509
+
+const struct dev_entry nics_intel_ee[] = {
+	{PCI_VENDOR_ID_INTEL, 0x150e, OK, "Intel", "82580 Quad Gigabit Ethernet Controller (Copper)"},
+	{PCI_VENDOR_ID_INTEL, 0x150f, NT , "Intel", "82580 Quad Gigabit Ethernet Controller (Fiber)"},
+	{PCI_VENDOR_ID_INTEL, 0x1510, NT , "Intel", "82580 Quad Gigabit Ethernet Controller (Backplane)"},
+	{PCI_VENDOR_ID_INTEL, 0x1511, NT , "Intel", "82580 Quad Gigabit Ethernet Controller (Ext. PHY)"},
+	{PCI_VENDOR_ID_INTEL, 0x1511, NT , "Intel", "82580 Dual Gigabit Ethernet Controller (Copper)"},
+	{PCI_VENDOR_ID_INTEL, UNPROG_DEVICE, OK, "Intel", "Unprogrammed 82580 Quad/Dual Gigabit Ethernet Controller"},
+	{0},
+};
+
+static int nicintel_ee_probe(struct flashctx *flash)
+{
+	if (nicintel_pci->device_id == UNPROG_DEVICE)
+		flash->chip->total_size = 16; /* Fall back to minimum supported size. */
+	else {
+		uint32_t tmp = pci_mmio_readl(nicintel_eebar + EEC);
+		tmp = ((tmp >> EE_SIZE) & EE_SIZE_MASK);
+		switch (tmp) {
+		case 7:
+			flash->chip->total_size = 16;
+			break;
+		case 8:
+			flash->chip->total_size = 32;
+			break;
+		default:
+			msg_cerr("Unsupported chip size 0x%x\n", tmp);
+			return 0;
+		}
+	}
+
+	flash->chip->page_size = PAGE_MASK + 1;
+	flash->chip->tested = TEST_OK_PREW;
+	flash->chip->gran = write_gran_1byte_implicit_erase;
+	flash->chip->block_erasers->eraseblocks[0].size = (PAGE_MASK + 1);
+	flash->chip->block_erasers->eraseblocks[0].count = (flash->chip->total_size * 1024) / (PAGE_MASK + 1);
+
+	return 1;
+}
+
+static int nicintel_ee_read_word(unsigned int addr, uint16_t *word)
+{
+	uint32_t tmp = BIT(EERD_START) | (addr << EERD_ADDR);
+	pci_mmio_writel(tmp, nicintel_eebar + EERD);
+
+	/* Poll done flag. 10.000.000 cycles seem to be enough. */
+	uint32_t i;
+	for (i = 0; i < 10000000; i++) {
+		tmp = pci_mmio_readl(nicintel_eebar + EERD);
+		if (tmp & BIT(EERD_DONE)) {
+			*word = (tmp >> EERD_DATA) & 0xffff;
+			return 0;
+		}
+	}
+
+	return -1;
+}
+
+static int nicintel_ee_read(struct flashctx *flash, uint8_t *buf, unsigned int addr, unsigned int len)
+{
+	uint16_t word;
+
+	/* The NIC interface always reads 16 b words so we need to convert the address and handle odd address
+	 * explicitly at the start (and also at the end in the loop below). */
+	if (addr & 1) {
+		if (nicintel_ee_read_word(addr / 2, &word))
+			return -1;
+		*buf++ = word & 0xff;
+		addr++;
+		len--;
+	}
+
+	while (len > 0) {
+		if (nicintel_ee_read_word(addr / 2, &word))
+			return -1;
+		*buf++ = word & 0xff;
+		addr++;
+		len--;
+		if (len > 0) {
+			*buf++ = (word >> 8) & 0xff;
+			addr++;
+			len--;
+		}
+	}
+
+	return 0;
+}
+
+static int nicintel_ee_bitset(int reg, int bit, bool val)
+{
+	uint32_t tmp;
+
+	tmp = pci_mmio_readl(nicintel_eebar + reg);
+	if (val)
+		tmp |= BIT(bit);
+	else
+		tmp &= ~BIT(bit);
+	pci_mmio_writel(tmp, nicintel_eebar + reg);
+
+	return -1;
+}
+
+/* Shifts one byte out while receiving another one by bitbanging (denoted "direct access" in the datasheet). */
+static int nicintel_ee_bitbang(uint8_t mosi, uint8_t *miso)
+{
+	uint8_t out = 0x0;
+
+	int i;
+	for (i = 7; i >= 0; i--) {
+		nicintel_ee_bitset(EEC, EE_SI, mosi & BIT(i));
+		nicintel_ee_bitset(EEC, EE_SCK, 1);
+		if (miso != NULL) {
+			uint32_t tmp = pci_mmio_readl(nicintel_eebar + EEC);
+			if (tmp & BIT(EE_SO))
+				out |= BIT(i);
+		}
+		nicintel_ee_bitset(EEC, EE_SCK, 0);
+	}
+
+	if (miso != NULL)
+		*miso = out;
+
+	return 0;
+}
+
+/* Polls the WIP bit of the status register of the attached EEPROM via bitbanging. */
+static int nicintel_ee_ready(void)
+{
+	unsigned int i;
+	for (i = 0; i < 1000; i++) {
+		nicintel_ee_bitset(EEC, EE_CS, 0);
+
+		nicintel_ee_bitbang(JEDEC_RDSR, NULL);
+		uint8_t rdsr;
+		nicintel_ee_bitbang(0x00, &rdsr);
+
+		nicintel_ee_bitset(EEC, EE_CS, 1);
+		programmer_delay(1);
+		if (!(rdsr & SPI_SR_WIP)) {
+			return 0;
+		}
+	}
+	return -1;
+}
+
+/* Requests direct access to the SPI pins. */
+static int nicintel_ee_req(void)
+{
+	uint32_t tmp;
+	nicintel_ee_bitset(EEC, EE_REQ, 1);
+
+	tmp = pci_mmio_readl(nicintel_eebar + EEC);
+	if (!(tmp & BIT(EE_GNT))) {
+		msg_perr("Enabling eeprom access failed.\n");
+		return 1;
+	}
+
+	nicintel_ee_bitset(EEC, EE_SCK, 0);
+	return 0;
+}
+
+static int nicintel_ee_write(struct flashctx *flash, const uint8_t *buf, unsigned int addr, unsigned int len)
+{
+	if (nicintel_ee_req())
+		return -1;
+
+	int ret = -1;
+	if (nicintel_ee_ready())
+		goto out;
+
+	while (len > 0) {
+		/* WREN */
+		nicintel_ee_bitset(EEC, EE_CS, 0);
+		nicintel_ee_bitbang(JEDEC_WREN, NULL);
+		nicintel_ee_bitset(EEC, EE_CS, 1);
+		programmer_delay(1);
+
+		/* data */
+		nicintel_ee_bitset(EEC, EE_CS, 0);
+		nicintel_ee_bitbang(JEDEC_BYTE_PROGRAM, NULL);
+		nicintel_ee_bitbang((addr >> 8) & 0xff, NULL);
+		nicintel_ee_bitbang(addr & 0xff, NULL);
+		while (len > 0) {
+			nicintel_ee_bitbang((buf) ? *buf++ : 0xff, NULL);
+			len--;
+			addr++;
+			if (!(addr & PAGE_MASK))
+				break;
+		}
+		nicintel_ee_bitset(EEC, EE_CS, 1);
+		programmer_delay(1);
+		if (nicintel_ee_ready())
+			goto out;
+	}
+	ret = 0;
+out:
+	nicintel_ee_bitset(EEC, EE_REQ, 0); /* Give up direct access. */
+	return ret;
+}
+
+static int nicintel_ee_erase(struct flashctx *flash, unsigned int addr, unsigned int len)
+{
+	return nicintel_ee_write(flash, NULL, addr, len);
+}
+
+static const struct opaque_master opaque_master_nicintel_ee = {
+	.probe = nicintel_ee_probe,
+	.read = nicintel_ee_read,
+	.write = nicintel_ee_write,
+	.erase = nicintel_ee_erase,
+};
+
+static int nicintel_spi_shutdown(void *eecp)
+{
+	uint32_t old_eec = *(uint32_t *)eecp;
+	/* Request bitbanging and unselect the chip first to be safe. */
+	if (nicintel_ee_req() || nicintel_ee_bitset(EEC, EE_CS, 1))
+		return -1;
+
+	/* Try to restore individual bits we care about. */
+	int ret = nicintel_ee_bitset(EEC, EE_SCK, old_eec & BIT(EE_SCK));
+	ret |= nicintel_ee_bitset(EEC, EE_SI, old_eec & BIT(EE_SI));
+	ret |= nicintel_ee_bitset(EEC, EE_CS, old_eec & BIT(EE_CS));
+	/* REQ will be cleared by hardware anyway after 2 seconds of inactivity on the SPI pins (3.3.2.1). */
+	ret |= nicintel_ee_bitset(EEC, EE_REQ, old_eec & BIT(EE_REQ));
+
+	free(eecp);
+	return ret;
+}
+
+int nicintel_ee_init(void)
+{
+	if (rget_io_perms())
+		return 1;
+
+	struct pci_dev *dev = pcidev_init(nics_intel_ee, PCI_BASE_ADDRESS_0);
+	if (!dev)
+		return 1;
+
+	uint32_t io_base_addr = pcidev_readbar(dev, PCI_BASE_ADDRESS_0);
+	if (!io_base_addr)
+		return 1;
+
+	nicintel_eebar = rphysmap("Intel Gigabit NIC w/ SPI EEPROM", io_base_addr, MEMMAP_SIZE);
+	nicintel_pci = dev;
+	if (dev->device_id != UNPROG_DEVICE) {
+		uint32_t eec = pci_mmio_readl(nicintel_eebar + EEC);
+
+		/* C.f. 3.3.1.5 for the detection mechanism (maybe? contradicting the EE_PRES definition),
+		 * and 3.3.1.7 for possible recovery. */
+		if (!(eec & BIT(EE_PRES))) {
+			msg_perr("Controller reports no EEPROM is present.\n");
+			return 1;
+		}
+
+		uint32_t *eecp = malloc(sizeof(uint32_t));
+		if (eecp == NULL)
+			return 1;
+		*eecp = eec;
+
+		if (register_shutdown(nicintel_spi_shutdown, eecp))
+			return 1;
+	}
+
+	return register_opaque_master(&opaque_master_nicintel_ee);
+}
--- a/programmer.h
+++ b/programmer.h
@ -84,6 +84,9 @@ enum programmer {
 #if CONFIG_NICINTEL_SPI == 1
 	PROGRAMMER_NICINTEL_SPI,
 #endif
+#if CONFIG_NICINTEL_EEPROM == 1
+	PROGRAMMER_NICINTEL_EEPROM,
+#endif
 #if CONFIG_OGP_SPI == 1
 	PROGRAMMER_OGP_SPI,
 #endif
@ -416,6 +419,12 @@ int nicintel_spi_init(void);
 extern const struct dev_entry nics_intel_spi[];
 #endif

+/* nicintel_eeprom.c */
+#if CONFIG_NICINTEL_EEPROM == 1
+int nicintel_ee_init(void);
+extern const struct dev_entry nics_intel_ee[];
+#endif
+
 /* ogp_spi.c */
 #if CONFIG_OGP_SPI == 1
 int ogp_spi_init(void);