Annotate SST49LF004B quirks for TBL#.
Add TEST_OK_PRW which is useful when a PREW chip gets a new erase
routine.
Change a few erase function prototypes to use unsigned int instead of
int.
Corresponding to flashrom svn r731.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Luc Verhaegen <libv@skynet.be>
The __func__ variant is standardized in C99 and recommended to be
used instead of __FUNCTION__ in the gcc info page.
Only _very_ old versions of gcc did not know about __func__, but we've
been using both __func__ and __FUNCTION__ for a long while now, and
nobody complained about this, so all our users seem to use recent
enough compilers.
Corresponding to flashrom svn r711.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
This makes visual inspection and grepping a lot harder than necessary.
Remove line breaks where appropriate. Some error messages should end up
on stderr instead of just being displayed in verbose mode.
Thanks to Maciej Pijanka for testing.
Corresponding to flashrom svn r660.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
And even when it checks if the erase worked, the result of that check is
often ignored.
Convert all erase functions and actually check return codes
almost everywhere.
Check inside all erase_* routines if erase worked, not outside.
erase_sector_jedec and erase_block_jedec have changed prototypes to
enable erase checking.
Uwe successfully tested LPC on an CK804 box and SPI on some SB600 box.
Corresponding to flashrom svn r595.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Add external programmer delay functions so external programmers can
handle the delay on their own if needed.
Corresponding to flashrom svn r578.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Urja Rannikko <urjaman@gmail.com>
This eliminates the conflicting delay requirements for old and new chips
with the same probing sequence.
Corresponding to flashrom svn r569.
Signed-off-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Build-tested on 32bit x86.
Corresponding to flashrom svn r521.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Use chipaddr instead of volatile uint8_t * because when we access chips
in external flashers, they are not accessed via pointers at all.
Benefits: This allows us to differentiate between volatile machine
memory accesses and flash chip accesses. It also enforces usage
of chip_{read,write}[bwl] to access flash chips, so nobody will
unintentionally use pointers to access chips anymore. Some unneeded
casts are removed as well. Grepping for chip operations and machine
memory operations doesn't yield any false positives anymore.
Compile tested on 32 bit and 64 bit Linux.
Corresponding to flashrom svn r519.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
The semantic patch I used in r418 to make the original conversion to
accessor functions was missing one isomorphism:
a[b] <=> *(a+b)
The semantic patcher Coccinelle was used to create this patch. Semantic
patch follows:
@@
typedef uint8_t;
expression a;
volatile uint8_t *b;
@@
- b[a]
+ *(b + a)
@@
expression a;
volatile uint8_t *b;
@@
- *(b) = (a);
+ chip_writeb(a, b);
@@
volatile uint8_t *b;
@@
- *(b)
+ chip_readb(b)
@@
type T;
T b;
@@
(
chip_readb
|
chip_writeb
)
(...,
- (T)
- (b)
+ b
)
Corresponding to flashrom svn r498.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
When flashrom JEDEC code sends the ID command to the chip, it expects to
see IDs in the default flash location.
However, sometimes the chip does not react to the ID command, either
because it doesn't understand the command or because the command never
reached it. One way to detect this is to compare ID output with flash
chip contents for the same location. If they are identical, there is a
high chance you're not actually seeing ID output. Warn the user in that
case.
This patch helps a lot when a chip is not recognized and we want to
check if the probe responses are real IDs or just random flash chip
contents.
This should probably be added to all probe functions, but probe_jedec
is called for all sizes and thus flashrom will check this condition at
least once per size, making sure we can cross-match the warning.
Corresponding to flashrom svn r494.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: FENG Yu Ning <fengyuning1984@gmail.com>
Before we attempt trickery, we can simply rename the accessor functions.
Patch created with the help of Coccinelle.
Corresponding to flashrom svn r420 and coreboot v2 svn r3984.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Idwer Vollering <idwer_v@hotmail.com>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Right now we perform direct pointer manipulation without any abstraction
to read from and write to memory mapped flash chips. That makes it
impossible to drive any flasher which does not mmap the whole chip.
Using helper functions readb() and writeb() allows a driver for external
flash programmers like Paraflasher to replace readb and writeb with
calls to its own chip access routines.
This patch has the additional advantage of removing lots of unnecessary
casts to volatile uint8_t * and now-superfluous parentheses which caused
poor readability.
I used the semantic patcher Coccinelle to create this patch. The
semantic patch follows:
@@
expression a;
typedef uint8_t;
volatile uint8_t *b;
@@
- *(b) = (a);
+ writeb(a, b);
@@
volatile uint8_t *b;
@@
- *(b)
+ readb(b)
@@
type T;
T b;
@@
(
readb
|
writeb
)
(...,
- (T)
- (b)
+ b
)
In contrast to a sed script, the semantic patch performs type checking
before converting anything.
Tested-by: Joe Julian
Corresponding to flashrom svn r418 and coreboot v2 svn r3971.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: FENG Yu Ning <fengyuning1984@gmail.com>
We should follow data sheet timing, even if chips have been tested to answer
faster in the field.
Corresponding to flashrom svn r273 and coreboot v2 svn r3387.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
Run time is increased a few 100ms but this is needed for reliability.
I consider this trivial.
Corresponding to flashrom svn r262 and coreboot v2 svn r3373.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
Flash chips which can be detected by JEDEC probe routines all have
vendor IDs with correct parity. Use a parity check as additional hint
whether a vendor ID makes sense. Note: Device IDs have no parity
requirements whatsoever.
Corresponding to flashrom svn r231 and coreboot v2 svn r3308.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
The continuation ID code does not go further than checking for IDs of
the type 0x7fXX, but does this for vendor and product ID. The current
published JEDEC spec has a list where the largest vendor ID is 7 bytes
long, but all leading bytes are 0x7f. The list will grow in the future,
and using a 64bit variable will not be enough anymore.
Besides that, it seems that the location of the ID byte after the first
continuation ID byte is very vendor specific, so we may have to revisit
that code some time in the future.
(Suggestion for a new encoding:
Use a two-byte data type for the ID, the lower byte contains the only
non-0x7f byte, the upper byte contains the number of 0x7f bytes used as
prefix, which is the bank number minus 1 the vendor ID appears in.)
Add support for EON EN29F002AT.
Corresponding to flashrom svn r171 and coreboot v2 svn r3030.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
The JEDEC probe routine had a delay of 10 us after entering ID mode
and this was insufficient for the 29C020. The data sheet claims we
have to wait 10 ms, but tests have shown that 20 us suffice. Allow for
variations in chip delays with a factor of 2 safety margin.
Corresponding to flashrom svn r159 and coreboot v2 svn r2962.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
Corresponding to flashrom svn r151 and coreboot v2 svn r2873.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Also minor changes to remove tab-space combinations where possible.
Corresponding to flashrom svn r144 and coreboot v2 svn r2850.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <david.hendricks@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r136 and coreboot v2 svn r2768.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
No changes in content of the files.
Corresponding to flashrom svn r131 and coreboot v2 svn r2751.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Corresponding to flashrom svn r130 and coreboot v2 svn r2748.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Corresponding to flashrom svn r128 and coreboot v2 svn r2746.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Corresponding to flashrom svn r127 and coreboot v2 svn r2745.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
* Give decent names to virt_addr and virt_addr_2
* add some comments
* move virtual addresses to the end of the struct,
so they dont mess up the initializer.
Corresponding to flashrom svn r111 and coreboot v2 svn r2689.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
indent -npro -kr -i8 -ts8 -sob -l80 -ss -ncs *.[ch]
Some minor fixups were required, and maybe a few more cosmetic
changes are needed.
Corresponding to flashrom svn r108 and coreboot v2 svn r2643.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Added a check-reprogram loop in the same function, to come around the
high page write failure rate on some boards.
This patch includes the changes suggested by Ron to simplify the control
flow.
It also includes trivial changes by me to make flashrom build on newer
systems (libpci needs libz now). I also made a small type case compile
fix and proper return code handling in one or two places.
Corresponding to flashrom svn r78 and coreboot v2 svn r2505.
Signed-off-by: Giampiero Giancipoli <gianci@email.it>
Signed-off-by: Ronald G Minnich <rminnich@gmail.com>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
