Used for page erase on some chips (e.g. Numonyx M45PE and
Sanyo LF25FW series).
Corresponding to flashrom svn r1682.
Signed-off-by: Nikolay Nikolaev <evrinoma@gmail.com>
Reviewed-by: Steven Zakulec <spzakulec@gmail.com>
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
This adds support for the following chips:
- AT25F512, AT25F512A, AT25F512B
- AT25F1024, AT25F1024A
- AT25F2048
- AT25F4096
Besides the definitions of the the chips in flashchips.c this includes
- a dedicated probing method (probe_spi_at25f)
- pretty printing methods (spi_prettyprint_status_register_at25f*), and
- unlocking methods (spi_disable_blockprotect_at25f*)
Corresponding to flashrom svn r1637.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Wicked chip: No WRSR, no write enable command (but swallows our
default one without a problem), supports an auto-erasing page write
(but even without that page writes are recommended to write the
whole page i.e. operate on a completely erased page), mad
requirements on block refreshments if only partly written.
Found on my Intel D946GZIS and tested with my serprog in situ.
Using the page write by setting JEDEC_BYTE_PROGRAM to 0x11 and using
the spi_chip_write_256 command greatly improves performance and works
flawlessly.
Corresponding to flashrom svn r1616.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
This is used by the AT25F series (only?), but is generic enough to
reside in spi25.c. The only currently supported chip is the AT25F512B.
Other members of that series need some additional infrastructure code,
hence this patch adds the erase function to the AT25F512B only.
Corresponding to flashrom svn r1600.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Similar to modules using the opaque programmer framework (e.g. ICH Hardware
Sequencing) this uses a template struct flashchip element in flashchips.c with
a special probe function that fills the obtained values into that struct.
This allows yet unknown SPI chips to be supported (read, erase, write) almost
as if it was already added to flashchips.c.
Documentation used:
http://www.jedec.org/standards-documents/docs/jesd216 (2011-04)
W25Q32BV data sheet Revision F (2011-04-01)
EN25QH16 data sheet Revision F (2011-06-01)
MX25L6436E data sheet Revision 1.8 (2011-12-26)
Tested-by: David Hendricks <dhendrix@google.com>
on W25Q64CV + dediprog
Tested-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
on a 2010 MX25L6436E with preliminary (i.e. incorrect) SFDP implementation + serprog
Thanks also to Michael Karcher for his comments and preliminary review!
Corresponding to flashrom svn r1500.
Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Add paranoid checks for correct values in essential registers in the SB600/SB700/... SPI driver. If something else changes the values we
wrote, we will see severe read/write corruption.
sb600spi will now abort the access and return an error if it detects
this sort of corruption.
Note: This corruption can be caused by a few different events:
- IPMI/BMC/IMC accesses flash
- Other software accesses flash
The nature of flash access (read/write/ID/...) is irrelevant. Each such
access will cause corruption for all other accesses happening at the
same time.
Thanks to Matthias Kretz for testing this patch.
Corresponding to flashrom svn r1145.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Matthias Kretz <kretz@kde.org>
The AAI code rewrite in r1052 introduced a bug: The writelen of AAI
continuation is 3 bytes, but the code incorrectly had 6 bytes there.
This causes all AAI writes (except the first two bytes of a chip) to
fail. Thanks to den_m for reporting the bug and for testing the fix.
Corresponding to flashrom svn r1121.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Add support for Atmel AT25DF081A and AT25DQ161.
Some chips require EWSR before WRSR, others require WREN before WRSR,
and some support both variants. Add feature_bits to select the correct
SPI command, and default to EWSR.
Corresponding to flashrom svn r1115.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Steven Rosario
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Modernize SPI AAI code, blacklist IT87 SPI for AAI, allow AAI to run
without warnings on ICH/VIA SPI. Add some code to make conversion to
partial write possible for AAI.
Corresponding to flashrom svn r1052.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Some chips implement the RES (0xab) opcode, but they use a non-standard
two byte response instead of the usual one byte response. A two-byte
response has the accuracy of REMS and RDID, so don't check for REMS/RDID
availability before running a two-byte RES.
Corresponding to flashrom svn r1017.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
The code should work on Linux/*BSD/MacOSX and relies on the serial code
implementation in serial.c. Support for additional platforms (Windows)
will have to be added to serial.c for this to work. For tests without a
Bus Pirate (or with non-functional serial code) it is possible to
#define FAKE_COMMUNICATION in buspirate_spi.c.
Thanks to Sean Nelson for the SPI mode settings code. I tweaked it a bit
to make configuration from a commandline easier should anybody want that
feature.
Tested-by: Sean Nelson <audiohacked@gmail.com>
Corresponding to flashrom svn r772.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Some drivers support only a few combinations of read/write length and
return error otherwise. Having a distinct return code for this error
means we can handle it in upper layers.
Corresponding to flashrom svn r653.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Among others, I have seen the following problems: - The SPI opcode is
not supported by the controller. ICH-style controllers exhibit this if
SPI config is locked down. - The address in in a prohibited area. This
can happen on ICH for any access (BBAR) and for writes in chipset write
protected areas. - There is no SPI controller.
Introduce separate error codes for unsupported opcode and prohibited
address.
Add the ability to adjust REMS and RES addresses to the minium supported
read address with the help of spi_get_valid_read_addr(). That function
needs to call SPI controller specific functions like reading BBAR on
ICH.
Corresponding to flashrom svn r500.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
This has been tested by Uwe Hermann on an RS690/SB600 board.
Corresponding to flashrom svn r351 and coreboot v2 svn r3779.
Signed-off-by: Jason Wang <Qingpei.Wang@amd.com>
Reviewed-by: Joe Bao <zheng.bao@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
- probe_spi_rdid with opcode 0x9f, usually 3 bytes ID
- probe_spi_res with opcode 0xab, usually 1 byte ID
We are missing the following probe function:
- probe_spi_rems with opcode 0x90, usually 2 bytes ID
RDID provides best specifity (manufacturer, device class and device) and
RES is supported by quite a few old chips. However, RES only returns one
byte and there are multiple flash chips with different sizes on the
market and all of them have the same RES ID.
REMS is from the same age as RES, but it provides a manufacturer and a
device ID. It is therefore on par with the probing for parallel flash
chips and specific enough.
The order in which chips should be detected is as follows:
1. RDID
2. REMS
3. RES
Corresponding to flashrom svn r349 and coreboot v2 svn r3775.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
The AT45 series SPI chips are DataFlash EEPROMs which means they have
odd (non-power-of-two) sector sizes, but some of the DataFlash chips can
be configured or ordered with power-of-two sector sizes.
Add probe support for the following Atmel SPI chips:
AT25DF021
AT25DF041A
AT25DF081
AT25DF161
AT25DF321A
AT25DF641
AT25F512B
AT25FS010
AT25FS040
AT26DF041
AT26DF081A
AT26DF161
AT26DF161A
AT26DF321
AT26F004
AT45CS1282
AT45DB011D
AT45DB021D
AT45DB041D
AT45DB081D
AT45DB161D
AT45DB321C
AT45DB321D
AT45DB642D
Add an explanation why the following chips can't be probed:
AT45BR3214B
AT45D011
AT45D021A
AT45D041A
AT45D081A
AT45D161
AT45DB011
AT45DB011B
AT45DB021A
AT45DB021B
AT45DB041A
AT45DB081A
AT45DB161
AT45DB161B
AT45DB321
AT45DB321B
AT45DB642
Add the ID, but no probing function for this chip:
AT25F512A
Corresponding to flashrom svn r342 and coreboot v2 svn r3754.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andriy Gapon <avg@icyb.net.ua>
Acked-by: Myles Watson <mylesgw@gmail.com>
While writing a new SPI driver I fixed some things in the SPI code:
All calls to spi_command() had unneccessary #define duplications, and in some
cases the read count define could theoretically become harmful because NULL was
passed for the read buffer. Avoid a crash, should someone change the #defines.
I also noticed that the only caller of spi_page_program() was the it87 driver,
and spi_page_program() could only call back into the it87 driver. Removed the
function for easier-to-follow code and made it8716f_spi_page_program() static.
The ichspi driver's static page functions are already static.
Corresponding to flashrom svn r302 and coreboot v2 svn r3418.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
Add support for the JEDEC RES (Read Electronic Signature and Resume from
Powerdown) SPI command to identify older SPI chips which can't handle
JEDEC RDID.
Since RES gives a one-byte identifier which is shared among many
different vendors and even different sizes, we want to match RES as a
last resort if RDID returns 0xff 0xff 0xff.
Corresponding to flashrom svn r235 and coreboot v2 svn r3320.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
This is a heavily reworked version of a patch by Fredrik Tolf, which was
Signed-off-by: Fredrik Tolf <fredrik@dolda2000.com>
This patch has no code changes.
Corresponding to flashrom svn r228 and coreboot v2 svn r3302.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
