The rayer_spi driver defaults to the RayeR cable, but selecting other
predefined pin layouts with the type= parameter is possible:
flashrom -p rayer_spi:type=xilinx
Corresponding to flashrom svn r1437.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
Remove the array spi_programmer, replace it by dynamic registration
instead. Also initially start with no busses supported, and switch to
the default non-SPI only for the internal programmer.
Also this patch changes the initialization for the buses_supported variable
from "everything-except-SPI" to "nothing". All programmers have to set the
bus type on their own, and this enables register_spi_programmer to just add
the SPI both for on-board SPI interfaces (where the internal programmer
already detected the other bus types), as well as for external programmers
(where we have the default "none").
Corresponding to flashrom svn r1299.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Allow specification of an alternate base address with
flashrom -p rayer_spi:iobase=0x278
Any base address is allowed as long as it is nonzero, below 65536 and a
multiple of four.
Read speed is now on par with original spipgm.exe.
Corresponding to flashrom svn r1188.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Martin Rehak <rayer@seznam.cz>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Programmer specific functions are of absolutely no interest to any file
except those dealing with programmer specific actions (special SPI
commands and the generic core).
The new header structure is as follows (and yes, improvements are
possible):
flashchips.h flash chip IDs
chipdrivers.h chip-specific read/write/... functions
flash.h common header for all stuff that doesn't fit elsewhere
hwaccess.h hardware access functions
programmer.h programmer specific functions
coreboot_tables.h header from coreboot, internal programmer only
spi.h SPI command definitions
Corresponding to flashrom svn r1112.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
To use the RayeR driver, run
flashrom -p rayer_spi -V
Known bugs/limitations:
- Won't compile/work on non-x86 architectures.
- Will always use direct port I/O access.
Log follows:
flashrom v0.9.2-r1039 on MS-DOS 7 (i686), built with libpci 3.1.5, GCC
4.3.2, little endian
Calibrating delay loop... OK.
Initializing rayer_bitbang_spi programmer
Using port 0x378 as I/O base for parallel port access.
...
Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1
0xc2, id2 0x2015
...
Found chip "Macronix MX25L1605" (2048 KB, SPI) at physical address
0xffe00000.
...
No operations were specified.
Corresponding to flashrom svn r1093.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Martin Rehak <rayer@seznam.cz>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
