Huge thanks go to Michael Karcher for reverse engineering the interface
and to Johannes Sjölund for testing the first iterations of my patch on
his hardware until it worked.
Thanks to the following testers of the patch:
* MCP61, 10de:03e0, LPC OK, ECS Geforce6100SM-M, Andrew Cleveland
* MCP61, 10de:03e0, LPC OK, Biostar NF520-A2 NF61D-A2, Vitaliy Buchynskyy
* MCP65, 10de:0441, SPI OK, MSI MS-7369 K9N Neo-F v2, Kjell Braden
* MCP65, 10de:0441, SPI OK, MSI MS-7369, Wolfgang Schnitker
* MCP65, 10de:0441, SPI OK, MSI MS-7369, Johannes Sjölund
* MCP65, 10de:0441, SPI OK, MSI MS-7369, Melchior Franz
* MCP78S, 10de:075c, SPI OK, Asus M3N78 PRO, Brad Rogers
* MCP78S, 10de:075c, SPI OK, Asus M3N78-VM, Marcel Partap
* MCP78S, 10de:075c, SPI OK, Asus M4N78 PRO, Kimmo Vuorinen
* MCP78S, 10de:075c, SPI OK, Asus M4N78 PRO, Vikram Ambrose
* MCP79, 10de:0aad, SPI OK, Acer Aspire R3600, Andrew Morgan
* MCP79, 10de:0aae, LPC ??, Lenovo Ideapad S12 laptop, Christian Schmitt
* MCP79, 10de:0aae, SPI OK, Apple iMac9,1 Mac-F2218EA9, David "dledson"
flashrom will refuse to write/erase for safety reasons if MCP6x/MCP7x
SPI is detected.
Corresponding to flashrom svn r1113.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Programmer specific functions are of absolutely no interest to any file
except those dealing with programmer specific actions (special SPI
commands and the generic core).
The new header structure is as follows (and yes, improvements are
possible):
flashchips.h flash chip IDs
chipdrivers.h chip-specific read/write/... functions
flash.h common header for all stuff that doesn't fit elsewhere
hwaccess.h hardware access functions
programmer.h programmer specific functions
coreboot_tables.h header from coreboot, internal programmer only
spi.h SPI command definitions
Corresponding to flashrom svn r1112.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
To use the RayeR driver, run
flashrom -p rayer_spi -V
Known bugs/limitations:
- Won't compile/work on non-x86 architectures.
- Will always use direct port I/O access.
Log follows:
flashrom v0.9.2-r1039 on MS-DOS 7 (i686), built with libpci 3.1.5, GCC
4.3.2, little endian
Calibrating delay loop... OK.
Initializing rayer_bitbang_spi programmer
Using port 0x378 as I/O base for parallel port access.
...
Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1
0xc2, id2 0x2015
...
Found chip "Macronix MX25L1605" (2048 KB, SPI) at physical address
0xffe00000.
...
No operations were specified.
Corresponding to flashrom svn r1093.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Martin Rehak <rayer@seznam.cz>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Actually check if the unlock worked instead of just assuming it worked.
Corresponding to flashrom svn r1082.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Use this instead of the open-coding variant that only aborts after it is too late.
Corresponding to flashrom svn r1081.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
However, wrap the write functions in a compat layer to allow converting
the rest of flashrom later. Tested on Intel NM10 by David Hendricks.
Corresponding to flashrom svn r1080.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Constify variables where possible.
Initialize programmer-related variables explicitly in programmer_init to
allow running programmer_init from a clean state after
programmer_shutdown.
Prohibit registering programmer shutdown functions before init or after
shutdown.
Kill some dead code.
Rename global variables with namespace-polluting names.
Use a previously unused locking helper function in sst49lfxxxc.c.
This is needed for libflashrom.
Effects on the binary size of flashrom are minimal (300 bytes
shrinkage), but the data section shrinks by 4384 bytes, and that's a
good thing if flashrom is operating in constrained envionments.
Corresponding to flashrom svn r1068.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
This allows using the dummy flasher for SPI read debugging.
Corresponding to flashrom svn r1053.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Use a blacklist instead of a whitelist for 4-byte SPI RDID.
Tell users where to report bugs.
Corresponding to flashrom svn r1051.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
CONFIG_FT2232SPI (makefile config option)
FT2232_SPI_SUPPORT (#define)
ft2232spi (programmer name)
ft2232_spi.c (programmer file)
Use CONFIG_* with underscores for makefile config options and #defines
and kill the useless _SUPPORT idiom.
Use lowercase names with underscores for programmer names and programmer
files.
With this, you can run "grep -i ft2232_spi" and find everything related
to the ft2232_spi driver. Same applies to all other programmers.
Corresponding to flashrom svn r1023.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Unistd.h was only used to get a definition of NULL in all files. Add our
own NULL #define and remove unistd.h from flash.h
stdio.h has no place in flash.h, it should be included only in files
which really need it.
Add #include statements in individual .c files where needed.
Replace a few printf with msg_* to eliminate the need for stdio.h.
Corresponding to flashrom svn r1021.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
ICH SPI can enforce address restrictions for all accesses which take an
address (well, it could if the chipset implementation was not broken).
Since exploiting the broken implementation is harder than conforming
to the address restrictions wherever possible, conform to the address
restrictions instead. This patch eliminates a lot of transaction errors
people were seeing on chip probe.
Corresponding to flashrom svn r1016.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
- x86/x86_64 (little endian)
- PowerPC (big endian)
- MIPS (big+little endian)
No changes to programmer specific code. This means any drivers with MMIO
access will _not_ suddenly start working on big endian systems, but with
this patch everything is in place to fix them.
Compilation should work on all architectures listed above for all
drivers except nic3com and nicrealtek which require PCI Port IO which is
x86-only for now.
To compile without nic3com and nicrealtek, run
make distclean
make CONFIG_NIC3COM=no CONFIG_NICREALTEK=no
Thanks to Misha Manulis for testing early versions of this patch on
PowerPC (big endian) with the satasii programmer.
Thanks to Segher Boessenkool for design review and for helping out with
compiler tricks and pointing out that we need eieio on PowerPC.
Thanks to Vladimir Serbinenko for compile testing on MIPS (little
endian) and PowerPC (big endian) and for runtime testing on MIPS (little
endian).
Thanks to David Daney for compile testing on MIPS (big endian).
Thanks to Uwe Hermann for compile and runtime testing on x86_64.
DO NOT RUN flashrom ON NON-X86 AFTER APPLYING THIS PATCH!
This patch only provides the infrastructure, but does not convert any
drivers, so flashrom will compile, but it won't do the right thing on
non-x86 platforms.
Corresponding to flashrom svn r1013.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Misha Manulis <misha@manulis.com>
Acked-by: Vladimir 'phcoder/φ-coder' Serbinenko <phcoder@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Convert programmer print messages to msg_p* convert general print messages to msg_g* a few fixes as suggested by Carl-Daniel.
Corresponding to flashrom svn r997.
Signed-off-by: Sean Nelson <audiohacked@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Corresponding to flashrom svn r964.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
SPI RES is the most unreliable way to identify chips because it only
returns a 1-byte ID for most chips.
For every given ID out there, probably a dozen incompatible flash
chips match it. We already refuse to identify a chip with RES if that
chip responds to RDID (3 bytes, good match), and with this patch we
additionally refuse RES if the chip responds to REMS (2 bytes, still a
good match). This increases matching accuracy a lot.
Besides that, the RDID/REMS response checking has been cleaned up for
better readability.
Corresponding to flashrom svn r899.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Speed up reads by a factor of 4 by switching block size from 4 to 16.
Add support for 4 byte RDID.
Add USB error decoding via usb_strerror.
Corresponding to flashrom svn r879.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Reverse engineered from USB logs. I never touched that programmer nor
did I ever see the associated software.
Disabled by default until it is complete. The driver needs to be hooked
up to the SPI core before it will do anything besides init and
diagnostics.
I successfully reverse engineered all commands, but some are still
somewhat magic.
Logs from "flashrom -p dediprog -V" are appreciated.
Probe and read should work, erase/write is expected to explode.
The programmer will set voltage to 0 on exit.
Thanks a lot to Stefan Reinauer and Patrick Georgi for providing USB
logs and for testing the result.
Corresponding to flashrom svn r870.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Some mingw declares a global identifier "byte", causing -Werror -Wshadow
to break compilation. This patch renames all identifiers called "byte".
Corresponding to flashrom svn r861.
Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Make various pieces of code conditional on support for internal
programming. Code shared between PCI device programmers and onboard
programming is now conditional as well.
It is now possible to build only with dummy support:
make CONFIG_INTERNAL=no CONFIG_NIC3COM=no CONFIG_SATASII=no
CONFIG_DRKAISER=no CONFIG_SERPROG=no CONFIG_FT2232SPI=no
This allows building for a specific use case only, and it also
facilitates porting to a new architecture because it is possible to
focus on highlevel code only.
Note: Either internal or dummy programmer needs to be compiled in due to
the current behaviour of always picking a default programmer if -p is
not specified. Picking an arbitrary external programmer as default
wouldn't make sense.
Build and runtime tested in all 1024 possible build combinations. The
only failures are by design as mentioned above.
Corresponding to flashrom svn r797.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
Example usage:
flashrom -p buspiratespi:spispeed=2.6MHz,dev=/dev/foo
flashrom -p buspiratespi:dev=/dev/foo,spispeed=2.6M
Refactor programmer option parsing (this allows cleanups in other
programmers as well).
Increase SPI read size from 8 to 12 bytes (current single-transaction
limit of the Bus Pirate raw SPI protocol).
Add Bus Pirate to the list of programmers supporting 4 byte RDID.
Add Bus Pirate syntax to the man page.
Tested-by: Sean Nelson <audiohacked@gmail.com>
Corresponding to flashrom svn r776.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Sean Nelson <audiohacked@gmail.com>
The code should work on Linux/*BSD/MacOSX and relies on the serial code
implementation in serial.c. Support for additional platforms (Windows)
will have to be added to serial.c for this to work. For tests without a
Bus Pirate (or with non-functional serial code) it is possible to
#define FAKE_COMMUNICATION in buspirate_spi.c.
Thanks to Sean Nelson for the SPI mode settings code. I tweaked it a bit
to make configuration from a commandline easier should anybody want that
feature.
Tested-by: Sean Nelson <audiohacked@gmail.com>
Corresponding to flashrom svn r772.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Sean Nelson <audiohacked@gmail.com>
If a chip is not on the RDID generic vendor list nor on the REMS
specific ID list, flashrom will claim that no chip is there.
Handle these cases gracefully. flashrom will ignore generic matches if a
specific chip was found, so this will have no impact on supported chips,
but help a lot for a first quick analysis by the user or developer. The
only drawback is that unknown chips may be recognized multiple times
until they are added to flashchips.[ch].
Corresponding to flashrom svn r767.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Marc Jones <marcj303@gmail.com>
Vincent wrote: This patch provided help to debug the partial write on
ICH in descriptor mode.
Corresponding to flashrom svn r764.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Vincent S. Cojot <openlook@cojot.name>
With the multicommand infrastructure I introduced in r645, it became
possible to integrate ICH SPI preopcodes cleanly into the flashrom
design.
The new code checks for every opcode in a multicommand array if it is a
preopcode. If yes, it checks if the next opcode is associated with that
preopcode and in that case it simply runs the opcode because the correct
preopcode will be run automatically before the opcode.
Corresponding to flashrom svn r727.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: FENG Yu Ning <fengyuning1984@gmail.com>
Example make commandline if you want only internal programmers:
make CONFIG_FT2232SPI=no CONFIG_SERPROG=no CONFIG_NIC3COM=no
CONFIG_SATASII=no CONFIG_DRKAISER=no CONFIG_DUMMY=no
Of course, all of the CONFIG_* symbols can be mixed and matched as
needed. CONFIG_FT2232SPI is special because even if it is enabled, make
will check if the headers are available and skip it otherwise.
Corresponding to flashrom svn r724.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
I decided to fill in the info for a
few chips to illustrate how this works both for uniform and non-uniform
sector sizes.
struct eraseblock{
int size; /* Eraseblock size */
int count; /* Number of contiguous blocks with that size */
};
struct eraseblock doesn't correspond with a single erase block, but with
a group of contiguous erase blocks having the same size.
Given a (top boot block) flash chip with the following weird, but
real-life structure:
top
16384
8192
8192
32768
65536
65536
65536
65536
65536
65536
65536
bottom
we get the following encoding:
{65536,7},{32768,1},{8192,2},{16384,1}
Although the number of blocks is bigger than 4, the number of block
groups is only 4. If you ever add some flash chips with more than 4
contiguous block groups, the definition will not fit into the 4-member
array anymore and gcc will recognize that and error out. No undetected
overflow possible. In that case, you simply increase array size a bit.
For modern flash chips with uniform erase block size, you only need one
array member anyway.
Of course data types will need to be changed if you ever get flash chips
with more than 2^30 erase blocks, but even with the lowest known erase
granularity of 256 bytes, these flash chips will have to have a size of
a quarter Terabyte. I'm pretty confident we won't see such big EEPROMs
in the near future (or at least not attached in a way that makes
flashrom usable). For SPI chips, we even have a guaranteed safety factor
of 4096 over the maximum SPI chip size (which is 2^24). And if such a
big flash chip has uniform erase block size, you could even split it
among the 4 array members. If you change int count to unsigned int
count, the storable size doubles. So with a split and a slight change of
data type, the maximum ROM chip size is 2 Terabytes.
Since many chips have multiple block erase functions where the
eraseblock layout depends on the block erase function, this patch
couples the block erase functions with their eraseblock layouts.
struct block_eraser {
struct eraseblock{
unsigned int size; /* Eraseblock size */
unsigned int count; /* Number of contiguous blocks with that size */
} eraseblocks[NUM_ERASEREGIONS];
int (*block_erase) (struct flashchip *flash, unsigned int blockaddr, unsigned int blocklen);
} block_erasers[NUM_ERASEFUNCTIONS];
Corresponding to flashrom svn r719.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
The __func__ variant is standardized in C99 and recommended to be
used instead of __FUNCTION__ in the gcc info page.
Only _very_ old versions of gcc did not know about __func__, but we've
been using both __func__ and __FUNCTION__ for a long while now, and
nobody complained about this, so all our users seem to use recent
enough compilers.
Corresponding to flashrom svn r711.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
We can't remove ft2232_spi.o from unconditional OBJS yet due to our
makefile structure (make features), but this patch adds #ifdefs around
all FT2232H code, so the net effect is the same.
Corresponding to flashrom svn r691.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Some SPI chip drivers and the generic 1-byte SPI chip write functions
didn't include the automatic erase present in other chip drivers.
Since the majority is definitely auto-erase, change the remaining
explicit-erase cases to be auto-erase as well.
Corresponding to flashrom svn r673.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carlos Arnau Perez <cemede@gmail.com>
If we only send an opcode and no additional data/address, the SPI
controller will read one byte too few from the chip. Basically, the
last byte of the chip response is discarded and will not end up in the
FIFO. It is unclear if the CS# line is set high too early as well. That
hardware bug is undocumented as of now, but I'm working with AMD to add
a detailed description of it to the errata.
Add loads of additional debugging to SB600/SB700 init.
Add explanatory comments for unintuitive code flow.
Thanks go to Uwe for testing quite a few iterations of the patch.
Kill the SB600 flash chip status register special case, which was a
somewhat misguided workaround for that hardware erratum.
Note for future added features in the SB600 SPI driver: It may be
possible to read up to 15 bytes of command response with overlapping
reads due to the ring buffer design of the FIFO if the command can be
repeated without ill effects. Same for skipping up to 7 bytes between
command and response.
Corresponding to flashrom svn r661.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
This makes visual inspection and grepping a lot harder than necessary.
Remove line breaks where appropriate. Some error messages should end up
on stderr instead of just being displayed in verbose mode.
Thanks to Maciej Pijanka for testing.
Corresponding to flashrom svn r660.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
This brings the SPI code in line with the generic programmer
infrastructure.
This patch is a reworked version of a patch by Jakob Bornecrantz.
Corresponding to flashrom svn r657.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Jakob Bornecrantz <wallbraker@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Jakob Bornecrantz <wallbraker@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Jakob Bornecrantz <wallbraker@gmail.com>
Corresponding to flashrom svn r651.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested it on Epia-m700 worked okay.
Acked-by: Jakob Bornecrantz <wallbraker@gmail.com>
Tested-by: Jakob Bornecrantz <wallbraker@gmail.com>
Corresponding to flashrom svn r650.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Jakob writes:
Tested it on my EPIA-m700 and it worked nice. Also double checked that
one of the changed functions actually ran.
Acked-by: Jakob Bornecrantz <wallbraker@gmail.com>
Once the ICH/VIA SPI driver is converted to multicommand, a lot of hacks
can disappear.
Corresponding to flashrom svn r647.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Jakob Bornecrantz <wallbraker@gmail.com>
Acked-by: Jakob Bornecrantz <wallbraker@gmail.com>
Some SPI opcodes need to be sent in direct succession after each other
without any chip deselect happening in between. A prominent example is
WREN (Write Enable) directly before PP (Page Program). Intel calls the
first opcode in such a row "preopcode".
Right now, we ignore the direct succession requirement completely and it
works pretty well because most onboard SPI masters have a timing or
heuristics which make the problem disappear.
The FT2232 SPI flasher is different. Since it is an external flasher,
timing is very different to what we can expect from onboard flashers and
this leads to failure at slow speeds.
This patch allows any function to submit multiple SPI commands in a
stream to any flasher. Support in the individual flashers isn't
implemented yet, so there is one generic function which passes the each
command in the stream one-by-one to the command functions of the
selected SPI flash driver.
Tested-by: Jakob Bornecrantz <wallbraker@gmail.com>
Corresponding to flashrom svn r645.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Jakob Bornecrantz <wallbraker@gmail.com>
Since block erase functions do not know the block length (it's not
specified in any standard), block erase functions now get an additional
parameter blocklen. This enables flashrom to verify the erase result for
block erase functions at correct boundaries.
Tested by Uwe on SB600.
Corresponding to flashrom svn r630.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
FTDI support is autodetected during compilation.
Paul writes:
There are certainly possible improvements: The code has hard-coded
values for which interface of the ftdi chip to use (interface B was
chosen because libftdi seems to have trouble with A right now), what
clock rate use for the SPI interface (I've been running at 30Mhz, but
the patch sets it to 10Mhz), and possibly others. I think this means
that per-programmer options might be a good idea at some point.
Carl-Daniel writes:
There is one additional FIXME comment in the code, but AFAICS that
problem is not solvable with current libftdi.
Corresponding to flashrom svn r598.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
That means you can tell flashrom to read exactly bytes 12345-56789
(start 12345, length 44445) and it will not fetch a single byte more.
Uwe tested this on one LPC, one SPI, and one parallel flash board.
Corresponding to flashrom svn r596.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Flash.h not only contains function prototypes and general settings, it
also has a huge chunk of chip and vendor IDs in the middle.
Split them out into a separate flashchips.h and adjust #include wherever
needed.
Corresponding to flashrom svn r594.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Urja Rannikko <urjaman@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
This was partly due to a design problem in the abstraction layer.
There should be exactly two different functions for reading SPI chips:
- memory mapped reads
- SPI command reads.
Each of them should be contained in a separate function, optionally
taking parameters where needed.
This patch solves the problems mentioned above, shortens the code and
makes the code logic a lot more obvious.
Since open-coding the min() function leads to errors, include it in this
patch as well.
Corresponding to flashrom svn r589.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Add external programmer delay functions so external programmers can
handle the delay on their own if needed.
Corresponding to flashrom svn r578.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Urja Rannikko <urjaman@gmail.com>
