Mark both B150 and Q170 as tested (DEP, as writability depends on the
flash descriptor). B150 was found in a ThinkCentre M700 Tiny, and Q170
in a ThinkCentre M900 Tiny, both support internal flashing once coreboot
is flashed (and coreboot SPI flash lockdown is not enabled).
Change-Id: Iedf4c77e3228628ac1a8726c1a9b4fb733d63d40
Signed-off-by: Michał Kopeć <michal.kopec@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/87045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Add detection of Tiger Point chipsets based on SPI controller PCI ID.
Current detection is based on ESPI PCI ID only which limits the
flashrom operability to 2 out of many chipset variants.
TEST=Read flash on a platform with Intel Corporation Tiger Lake-LP
SPI Controller [8086:a0a4] and ISA bridge [0601]: Intel Corporation
Device [8086:a088] ESPI device.
Change-Id: Ie6859d81157760ca03fe34ba5ac311eba5a7c46b
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/84987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Based on public Intel 700 Series PCH datasheet, DOC 743835 rev 004.
The IDs of IoT chipset SKUs (ending with E) can only be found in "12th
Gen Intel® Core™ Processors Family (Formerly Known as Alder Lake -S)
for IoT Platforms External Design Specification (EDS) Addendum" DOC
634528 rev 2.7 (NDA).
TEST=Probe flash on Z790 chipset. Run the ich_descriptors_tool and
check the output is correct as expected.
Change-Id: I13ac52d5400c0e2260e12d605077fc2182c379ef
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/83854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Reviewed-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
In the latest pciutils(v3.13.0), it supports accessing pci registers
by ecam. This patch uses libpci version check to decide whether
flashrom calls libpci and use 0xcf8/0xcfc or ecam to access pci
registers.
BUG=b:359813524
TEST=with libpci >= 3.13.0, flashrom is working with ECAM access
Change-Id: I4549f87c8b01da0a1d3d8ce0b3b75c1f5fa2cbab
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/83896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hsuan-ting Chen <roccochen@google.com>
Reviewed-by: Peter Marheine <pmarheine@chromium.org>
Clean commit 51e1d0e4b7670e5822560acc724a6a8dd00b6af4
'Add support for Intel Emmitsburg PCH' which broke
CHIPSET_5_SERIES_IBEX_PEAK detection and which assumes C740 is the same
as C620, while its more a close relative to Intel's H570 PCH.
Based on Intel SPI Programming Guide #619386.
Test: Run on Intel ArcherCity CRB with Intel's C741 PCH
using the 'internal' programmer.
Test: Run on BMC and accessed the SPI flash chip over
'linux_mtd' programmer.
Change-Id: I80eebc0fcc14de9df823aceaee77870ad136f94a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/78186
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This file does not access any large files, so there's no need to define
this feature test macro.
Change-Id: I866cfa2f996eeea5846e5d9189647ad7a4a4e3e4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/75271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Reviewed-by: Alexander Goncharov <chat@joursoir.net>
DJGPP for compiling DOS has other sizes for the normal int types and
therefore throwing errors when using %i %d or %x with uint32_t.
Fix these warnings by using the macros created for it and provided in
inttypes.h.
Change-Id: Ia75b6df981ce60c891161fe553c7ceab8570178d
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/73040
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Due to how internal is structured around chipset_flash_enable()
entry we need to prepare a crafted programmer_cfg that contains
a board_enable substructure with data derived from the board_enable
subsystem. While this is certainly not perfection, it does make
clear the relationships between board_enable into chipset_flash_enable
and subsequently the overall internal programmer initialisation
in a RAII fashion at the type level over closure upon global
state that is impossible to reason about.
Also flip predicate in report_nonwl_laptop_detected() and
return early with the trivial base-case.
TEST=`$ sudo ./flashrom -p internal --flash-name`.
Change-Id: I459215253845c2af73262943ce91a36464e9eb06
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/73456
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Avoid global symbol shadowing in local functions.
Change-Id: Idfca0b7e46d8051bf680227250cf40483e19dc53
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/73646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Note that while I can read the chip, on my Lenovo Legion T5 28IMB05,
cannot write to the flash chip with any tools except upgrading with
vendor tool, no downgrades are allowed, due to the fact of SMM, even if
I did manage to flash the BIOS chip somehow, would still face bootguard
since this machine has bootguard. But if I read the chip, and verify my
read bin file, it works fine, until changing the SMBIOS, which is in
the vendor BIOS update package.
Change-Id: Id8fcb59d5dbafea3e79c4e3ad75484bbd163feca
Signed-off-by: Christopher Lentocha <christopherericlentocha@gmail.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/72056
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Tested reading, writing and erasing the flash chip of a Prodrive
Hermes mainboard with an Intel C246 PCH. However, since ME-enabled
chipsets are marked as DEP instead of OK, this one shall also be.
Change-Id: I07d6c4a60e468c61eba836db91e1335f4a762048
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/68594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Use the bool type instead of an integer for the variable `laptop_ok`,
since this represents its purpose much better.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I5d9fc3516bc2d29f11b056e35b3e5e324ce93423
Reviewed-on: https://review.coreboot.org/c/flashrom/+/66891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Use the bool type instead of an integer for the variable
`programmer_may_write`, since this represents its purpose much better.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I69958527ae018a92f1c42734a7990d0c532dee0c
Reviewed-on: https://review.coreboot.org/c/flashrom/+/66885
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Modify the type signature of the programmer entry-point
xxx_init() functions to allow for the consumption of the
programmer parameterisation string data.
Also plumb programmer_cfg though get_params.
Change-Id: I480589bb50b47fdf5af259d068f49fedfce88ea5
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/66661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Ran;
```
$ find -name '*.c' -exec sed -i 's/extract_programmer_param_str(NULL/extract_programmer_param_str(cfg/g' '{}' \;
```
Manually fix i2c_helper_linux.c and other cases after.
Treat cases of;
- pcidev.c , and
- usb_device.c
as exceptional to be dealt with in later patches.
Change-Id: If7b7987e803d35582dda219652a6fc3ed5729b47
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/66656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Modify the type signature of the programmer entry-point
xxx_init() functions to allow for the consumption of the
programmer parameterisation string data.
Also plumb programmer_cfg though handle_imc and handle_speed.
Change-Id: I82f9ee75df90c582ef345c00a5487c687f28cdd5
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/66660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
Results can be reproduced with the following invocation;
```
$ find -name '*.c' -exec sed -i 's/extract_programmer_param_str(/extract_programmer_param_str(NULL, /g' '{}' \;
```
This allows for a pointer to the actual programmer parameters
to be passed instead of a global.
Change-Id: I781a328fa280e0a9601050dd99a75af72c39c899
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/66654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Anastasia Klimchuk <aklm@chromium.org>
This patch changes the function name of extract_programmer_param() to
extract_programmer_param_str() as this function name will clearly
specify that it returns the value of the given parameter as a string.
Signed-off-by: Chinmay Lonkar <chinmay20220@gmail.com>
Change-Id: Id7b9fff4d3e1de22abd31b8123a1d237cd0f5c97
Reviewed-on: https://review.coreboot.org/c/flashrom/+/65521
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Additionally, utilize CSSO (CPU Soft Strap Offset) to uniquely detect
the chipset when the CSSL (CPU Soft Strap Length) field default value
(0x03) on Jasper Lake is the same as Elkhart Lake.
BUG=b:221175960
TEST=dedede with `flashrom -p internal --flash-size`.
```
$ flashrom -VVV -p internal --ifd -i fd -i bios -r /tmp/filename.rom
<snip>
Enabling hardware sequencing by default for 100+ series PCH.
OK.
No board enable found matching coreboot IDs vendor="Google", model="Magolor".
The following protocols are supported: Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Chip identified: GD25Q127C/GD25Q128C
Hardware sequencing reports 1 attached SPI flash chip with a density of 16384 kB.
There is only one partition containing the whole address space (0x000000 - 0xffffff).
There are 4096 erase blocks with 4096 B each.
Added layout entry 00000000 - 00ffffff named complete flash
Found GigaDevice flash chip "GD25Q127C/GD25Q128C" (16384 kB, Programmer-specific) mapped at physical address 0x0000000000000000.
Found GigaDevice flash chip "GD25Q127C/GD25Q128C" (16384 kB, Programmer-specific).
This chip may contain one-time programmable memory. flashrom cannot read
and may never be able to write it, hence it may not be able to completely
clone the contents of this chip (see man page for details).
Reading Status register
Block protection is disabled.
Reading ich descriptor... Reading 4096 bytes starting at 0x000000.
done.
Assuming chipset 'Jasper Lake'.
Added layout entry 00000000 - 00000fff named fd
Added layout entry 00381000 - 00ffffff named bios
Added layout entry 00001000 - 00380fff named me
restore_power_management: Re-enabling power management.
Using regions: "bios", "fd".
Reading Status register
Block protection is disabled.
Reading flash... 0x381000-0xffffff:R Reading 13103104 bytes starting at 0x381000.
000000-0x0fff:R Reading 4096 bytes starting at 0x000000.
done.
restore_power_management: Re-enabling power management.
SUCCESS
Restoring PCI config space for 00:1f:5 reg 0xdc
restore_power_management: Re-enabling power management.
```
Change-Id: Ib942d0b8942fe0a991b2af0b187414818485153d
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/62282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sam McNally <sammc@google.com>
This eliminates the need to redefine the rdmsr and wrmsr symbols,
resulting in more understandable code. The common prefix clarify the
relation between the functions.
Change-Id: Ie5ad54d198312578e0a1ee719eec67b37d2bf6a4
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/62851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds Meteor Lake support into flashrom.
Additionally, utilize CSSO (CPU Soft Strap Offset) to uniquely detect
the chipset when the CSSL (CPU Soft Strap Length) field default value
(0x03) on Meteor Lake is the same as Elkhart Lake.
BUG=b:224325352
TEST=Flashrom is able to detect MTL SPI DID and show chipset name as below:
> flashrom --flash-name
....
Found chipset "Intel Meteor Lake-P/M".
....
> flashrom - internal --ifd -i fd -i bios -r /tmp/bios.rom
....
Reading ich_descriptor... done.
Assuming chipset 'Meteor Lake'.
Using regions: "bios", "fd".
Reading flash... done.
SUCCESS
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I0a2ffe2ba8d96c90d89b77e0d8583d179ff02a75
Reviewed-on: https://review.coreboot.org/c/flashrom/+/62783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Sam McNally <sammc@google.com>
Does exactly what it says on the tin.
BUG=b:220799648
TEST=```localhost ~ # flashrom --flash-name
<snip>
Found Programmer flash chip "Opaque flash chip" (32768 kB, Programmer-specific) mapped at physical address 0x0000000000000000.
vendor="Programmer" name="Opaque flash chip"
flashrom -p internal --ifd -i fd -i bios -r /tmp/filename.rom
flashrom unknown on Linux 5.15.22 (x86_64)
flashrom is free software, get the source code at https://flashrom.org
Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
coreboot table found at 0x768a7000.
Found chipset "Intel Alder Lake-N".
Enabling flash write... Warning: Setting BIOS Control at 0xdc from 0x8b to 0x89 failed.
New value is 0x8b.
SPI Configuration is locked down.
OK.
Found Winbond flash chip "W25Q256JV_M" (32768 kB, Programmer-specific) mapped at physical address 0x0000000000000000.
Error accessing W25Q256JV_M, 0x2000000 bytes at 0x00000000fe000000
/dev/mem mmap failed: Resource temporarily unavailable
Could not map flash chip W25Q256JV_M at 0x00000000fe000000.
Reading ich descriptor... done.
Using regions: "bios", "fd".
Error accessing W25Q256JV_M, 0x2000000 bytes at 0x00000000fe000000
/dev/mem mmap failed: Resource temporarily unavailable
Could not map flash chip W25Q256JV_M at 0x00000000fe000000.
Reading flash... done.
SUCCESS
Also,
Reading ich descriptor... Reading 4096 bytes starting at 0x000000.
done.
Assuming chipset '600 series Alder Point'.
Added layout entry 00000000 - 00000fff named fd
Added layout entry 00500000 - 01ffffff named bios
Added layout entry 00001000 - 004fffff named me
```
Tested on Nivviks/ADL-N and Brya/ADL-P.
Change-Id: Ie66cf519df13f3391c41f5016b16a81ef3dfd4bf
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/62251
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Sam McNally <sammc@google.com>
Elkhart Lake has a chipset called Mule Creek Canyon which is quite
compatible with 300 series chipsets. There are a few differences though,
e.g. different encoding for the SPI clock values for read and write in
the FLCOMP register. In addition Elkhart Lake has a new PCI device ID
for the SPI controller which is added, too.
TEST=Read and flash complete flash on Siemens MC EHL1
Change-Id: I711e39a3ec9cd7098389231eaa1cb864d615a475
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/60711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The changes to hwaccess in commit 49d758698a0dd166679c48b1a2785e50e9b0cc83
cause build failure on non-x86 systems because the hwaccess_x86_*
headers are included in some files that are built for all platforms
(particularly those in the internal programmer) and those headers in
turn include <sys/io.h> which only exists on x86.
This change avoids including those headers on non-x86 platforms so
the internal programmer can be built without errors.
The comment on the stub implementation of rget_io_perms() is also
modified to remove references to non-x86 platforms, since that file is
only built on x86 now.
BUG=None
TEST=meson build succeeds for both x86 and ARM targets
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Change-Id: I20f122679c30340b2c73afd7419e79644ddc3c4e
Reviewed-on: https://review.coreboot.org/c/flashrom/+/61194
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Thomas Heijligen <src@posteo.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The mmio_le/be_read/writex functions are used for raw memory access.
Bundle them with the physmap functions.
Change-Id: I313062b078e89630c703038866ac93c651f0f49a
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/61160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Line up physmap with the other hwaccess related code.
Change-Id: Ieba6f4e94cfc3e668fcb8b3c978de5908aed2592
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/60113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Allow x86 msr related code to be compiled independent from memory
mapping functionality. This enables for a better selection of needed
hardware access types.
Change-Id: Idc9ce9df3ea1e291ad469de59467646b294119c4
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/60111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Allow port I/O related code to be compiled independent from memory
mapping functionality. This enables for a better selection of needed
hardware access types.
Change-Id: I372b4a409f036da766c42bc406b596bc41b0f75a
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/60110
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Split the include of hwaccess and libpci. There is no need to have pci.h
included in hwaccess.
Change-Id: Ibf00356f0ef5cc92e0ec99f8fe5cdda56f47b166
Signed-off-by: Thomas Heijligen <thomas.heijligen@secunet.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/58883
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tiger Lake has very low ICCRIBA (TGL=0x11, CNL=0x34 and CML=0x34) and
detects as unknown chipset compatible with 300 series chipset. Add a
new enum CHIPSET_500_SERIES_TIGER_POINT and treat it identically to
CHIPSET_400_SERIES_COMET_POINT. There are some exceptions though,
ICCRIBA is no longer present n descriptor content so a new union has
been defined for new fields and used in descriptor guessing.
freq_read field is not present on Tiger Lake, moreover in CannonPoint
and Comet Point this field is used as eSPI/EC frequency, so a new
function to print read frequency has ben added. Finally Tiger lake
boot straps include eSPI, so a new bus has been added for the new
straps.
TEST=Flash BIOS region on Intel i5-1135G7
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I28f3b6fe9f8ce9e976a6808683f46b6f4ec72bdd
Reviewed-on: https://review.coreboot.org/c/flashrom/+/55578
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch does the following:
- Add PCIe ID for Intel Emmitsburg PCH
- Based on ICH descriptor content, choose CHIPSET_C620_SERIES_LEWISBURG
if ISL/PSL is 80.
TESTED=tried on a server with Intel Emmitsburg PCH, flash update
was successful. This server, however, does not have flash chip
installed, it instead has em100 emulator connected.
Change-Id: I2a1bb7467e693d1583aa885fa0e277075edd4a3e
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: David Hendricks <ddaveh@amazon.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/54965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Tim Chu <Tim.Chu@quantatw.com>
The SPI hardware is pretty much unchanged from Apollo Lake. However, the
IFD differs significantly enough to require special handling.
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Change-Id: Ib5dcdf204166f44a8531c19b5f363b851d2ccd77
Reviewed-on: https://review.coreboot.org/c/flashrom/+/54276
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
